Temperature forcing system

Search results for "Temperature forcing system"

17 products found

QUADPRO2ASemi-automatic 4 point probe measurement under temperature

Semi-automatic 4-point in-line temperature measurement system on samples ranging from 10mm to 300mm in diameter.. Capable of measuring surface resistance ranges from 10μΩ/sq to 10GΩ/sq. Several versions possibles to optimize measurement accuracy according to the ranges measured.

Equipment feature:

• V/I measurement, sheet resistance, resistivity or thickness
• Mean, Standard Deviation, Minimum, Maximum and 3Sigma reports for the dataset
• Temperature Coefficient of Resistance (TCR) measurements
• Automated 2D mapping, 3D mapping and cross-section
• Ultra high precision and repeatability
• Comparative mapping

The TCR option

The Resistance Temperature Coefficient option integrates sample temperature control as well as automated injected current control and resistance calculations. Integrated with a thermal chuck system, the test automatically sweeps temperatures over a wide range without moving the test tips.
Measurements are taken at each target temperature and the results are plotted on a graph. The TCR is expressed in parts per million (PPM). Users define the temperature range, steps, and delay for each test point before taking a measurement. A variety of thermal chucks are available to set the range and resolution from room temperature to 300°C, with 1° resolution.
Data can be printed or exported to a spreadsheet for further analysis.

HMS5000Semi-automatic Hall Effect measurement system with temperature

The HMS5000 is a motorized Hall effect measurement system dedicated to the electrical characterization of semiconductor materials using the Van der Pauw method. Designed to accommodate samples of varying compositions and geometries, it enables the precise extraction of numerous essential electrical parameters.
Compatible with temperature measurements from 77 K to 350 K, the HMS5000 offers a complete solution for the analysis of semiconductor thin films.

Thanks to its versatility, the system is suitable for both research activities and development and quality control applications in the fields of advanced materials and microelectronics.

The HMS5000 also integrates dedicated software that verifies the quality of ohmic contacts through the automatic plotting of I-V curves, thus ensuring the reliability and reproducibility of measurements. It also allows for the management of magnet movement and temperature ramps to plot the response of your sample.

It is therefore possible to calculate:

• Charge carrier mobility
• Majority carrier density (dopants)
• Doping type (P/N ratio)
• Hall voltage / Hall coefficient
• Surface resistance, resistivity, conductivity

Features:

• Sample size: 5x5mm - 20x20mm
• Motorized dual magnets: 0.5T
• Measurement under temperature: 77K to 350K
• Current range: 1nA - 20mA

Applications:

- Si, Ge, SiGe, SiC, GaAs, InGaAs, InP, GaN, ZnO, TCOs
- Optoelectronic component
- Nanomaterials - Sensors, MEMS
- Conductive polymer
- Oxide deposit
- Ceramic & Glass
- Batteries
- Electrodes
- Photovoltaic

ProbeSenseTemperature measurement sensor

ProbeSense™ is a patent-pending device for temperature calibration between -65°C to 300°C.

Temperature has always been an important parameter when testing sensor devices, but now the trend is moving from simple, functional tests to calibration at certain temperatures. To meet the requirements of devices like temperature, gas, humidity and pressure sensors, ERS has developed a unique solution that enables highly accurate temperature measurements over the whole chuck.

The device is called ProbeSense™: a unique temperature calibration tool, that consists of only one sensor. It is mounted in the probe card position of the prober and connected to a calibration instrument, where accuracy below 30mK can be reached. A fully automated calibration process is also possible with an integration of the ProbeSense™ in a software.

ProbeSense™ comes delivered in a robust, custom-made suitcase and contains the following components:

• ProbeSense™ with a calibrated sensor down to 10mK
• Adapter plate(s) for your prober of choice
• Temperature measurement device cable
• Spare battery for the measurement device
• USB stick with ProbeSense™ software

HT4High temperature 4 point probe head

4-point head for high temperature and high resistivity, usable on equipment of the Pack4PP, Quadpro series and or for separate use. The standard head is designed in macor with 4 independent tips in tungsten or osmium. A bayonet and two screws make it easy to attach the tip to our 4-prong stand for precise and repeatable measurements.

Specifications:

• Material of the tips defined according to the type of layer to be measured
• Choice of parameters: Tip spacing (pitch), tip fineness, tip pressure
• Terminations: Flying leads, Banana jacks, Triax...

S725HTMicropositioner S725 for high temperature

This economic micropositioner will allow probe tips to land on pads or lines down to 20 µm.
Special model for temperature probe test measurement, up to 600°C.

QUADPRO2MManual 4 point probe measurement system

4-point manual in-line temperature measurement system on samples ranging from 10mm to 300mm in diameter.. Capable of measuring surface resistance ranges from 10μΩ/sq to 10GΩ/sq. Several versions possibles to optimize measurement accuracy according to the ranges measured.

Equipment feature:

• V/I measurement, sheet resistance, resistivity or thickness
• Mean, Standard Deviation, Minimum, Maximum and 3Sigma reports for the dataset
• Temperature Coefficient of Resistance (TCR) measurements
• Automated 2D mapping, 3D mapping and cross-section
• Ultra high precision and repeatability
• Comparative mapping

The TCR option

The Resistance Temperature Coefficient option integrates sample temperature control as well as automated injected current control and resistance calculations. Integrated with a thermal chuck system, the test automatically sweeps temperatures over a wide range without moving the test tips.
Measurements are taken at each target temperature and the results are plotted on a graph. The TCR is expressed in parts per million (PPM). Users define the temperature range, steps, and delay for each test point before taking a measurement. A variety of thermal chucks are available to set the range and resolution from room temperature to 300°C, with 1° resolution.
Data can be printed or exported to a spreadsheet for further analysis.

HP1000V-PSVacuum mini probe station

Compact probing station for high temperature measurements under vacuum.
This completely hermetic station allows you to go up to 1000°C while putting your sample under vacuum.
Tungsten Rhenium tips, very resistant to high temperature and reliable. These tips can be manipulated manually thanks to micropositioners, which facilitates their precise placement on pads whose size is greater than or equal to 10 µm.

Applications:

- Electrical test: resistor, transistor, capacitor
- Electrodes, diodes
- Photovoltaic
- Nanomaterials
- Sensors, MEMS, OLED, infrared...
- Silicon wafer
- Microchip

Specifications:

• Measurements on unit samples, 50x 50mm
• Manual positioning with 4 micropositioners (Up to 7 micropositioners)
• Temperature range: Ambient to 1000°C
• Vaccum chamber

HCP-400-S-100Square hot plate 100mm

This equipment suitable for research laboratories. A temperature range from -120°C to 400°C which allows a wide range of applications from bio-organisms to microelectronics.

Applications:

- Electrodes
- Nano-fluids
- Advanced Ceramics
- Metallic oxide
- Nanomaterials
- Microorganism
- Conductive polymer
- Batteries

Specifications:

• Temperature controller included
• Temperature range: -120°C to 400°C
• Chuck Square

UH104Manual UV curing system

Benchtop low-profile system, the UH104 offers an exceptional flexibility and repeatability in the curing of UV films for dicing or backgrinding.UV insolators are illumination systems allowing the rapid curing of all types of photo-sensitive materials. Mainly used in the semiconductor world, they solidify the glue present on the adhesive films used during the cutting process. Safe for the environment, this UV curing process takes place at room temperature and at a wavelength of 365nm.

Technical specifications:

• Compact 8" or 12" system
• Manual loading, automatic process
•Rectangular substrates up to 12"
• Environmentally friendly, ozone-free UV lamp
• Fast curing time
• Easily programmable microprocessor based controller
• Repeatable manual operation
• Exceptional cost/performance ratio
• Low temperature 365nm UVA curing process
• Very energy efficient
• Quartz glass window
• Lamp intensity measurement port

Options:

- Motorized and rotating work platform
- 6" or 8" film frame adapter
- UV Lamp Intensity Radiometer (requires sensor/attenuator assembly, below)
- Sensor/attenuator assembly (requires radiometer above)

HMS3000Manual Hall Effect measurement system

Discover our HMS3000 manual Hall effect system, designed for studying and characterizing the electrical properties of semiconductor materials and thin films. This educational and experimental equipment allows for the precise analysis of charge carrier mobility, carrier concentration, and resistivity of samples.

By measuring the voltages generated by Lorentz forces via its permanent magnet module, the system provides a concrete understanding of electronic transport phenomena and the effects of material doping. Compatible with the Van der Pauw method, it enables reliable measurements on various geometries and thin films.

Robust and easy to use, this manual Hall effect system is ideal for higher education laboratories, research centers, and characterization applications in semiconductor physics and materials science.

It is thus possible to calculate:

• Charge carrier mobility
• Majority carrier density (dopants)
• Doping type (P/N ratio)
• Hall voltage / Hall coefficient
• Surface resistances, resistivity, conductivity

Features:

• Sample size: 5x5 mm to 20x20 mm
• Measurement at two temperatures: ambient and 77 K
• Single or double magnet
• LN2 chamber
• ITO reference sample
• Different SPCB sample holders depending on the application

Applications:

- Si, Ge, SiGe, SiC, GaAs, InGaAs, InP, GaN, ZnO, TCOs
- Optoelectronic component
- Nanomaterials - Sensors, MEMS
- Conductive polymer
- Oxide deposit
- Ceramic & Glass
- Batteries
- Electrodes
- Photovoltaic

HMS5300Semi-automatic Hall Effect measurement system for high temperatures

Discover our HMS5300 semi-automatic Hall effect system, designed for studying and characterizing the electrical properties of semiconductor materials and thin films at varying temperatures. This educational and experimental equipment allows for the precise analysis of charge carrier mobility, carrier concentration, and sample resistivity.

By measuring the voltages generated under the influence of Lorentz forces via its permanent magnet module, the system provides a concrete understanding of electronic transport phenomena and the effects of material doping. Compatible with the Van der Pauw method, it enables reliable measurements on various geometries and thin films.

Robust and easy to use, this manual Hall effect system is ideal for higher education laboratories, research centers, and characterization applications in semiconductor physics and materials science.

Its semi-automatic temperature ramp system and magnetic field measurements make it completely autonomous during the measurement process.

It is therefore possible to calculate:

• Charge carrier mobility
• Majority carrier density (dopants)
• Doping type (P/N ratio)
• Hall voltage / Hall coefficient
• Surface resistance, resistivity, conductivity

Features:

• Sample size: 5x5mm - 20x20mm
• Motorized dual magnets: 0.5T
• Measurement under temperature: 77K to 350K
• Current range: 1nA - 20mA

Compatibles temperature modules:

- AMP55T-RTSK: Ambient or 77K
- AMP55T-SH80350K: From 77K to 350K
- AHT55T3: From 300K to 570K
- AHT55T5: From 300K to 770K

Applications:

- Si, Ge, SiGe, SiC, GaAs, InGaAs, InP, GaN, ZnO, TCOs
- Optoelectronic component - Nanomaterials
- Sensors, MEMS - Conductive polymer
- Oxide deposit
- Ceramic & Glass
- Batteries
- Electrodes
- Photovoltaic

HMS5500Semi-automatic Hall Effect measurement system for very high temperatures

Discover our HMS5500 semi-automatic Hall effect system, designed for studying and characterizing the electrical properties of semiconductor materials and thin films at varying temperatures. This educational and experimental equipment allows for the precise analysis of charge carrier mobility, carrier concentration, and sample resistivity.

By measuring the voltages generated under the influence of Lorentz forces via its permanent magnet module, the system provides a concrete understanding of electronic transport phenomena and the effects of material doping. Compatible with the Van der Pauw method, it enables reliable measurements on various geometries and thin films.

Robust and easy to use, this manual Hall effect system is ideal for higher education laboratories, research centers, and characterization applications in semiconductor physics and materials science.

Its semi-automatic temperature ramp system and magnetic field measurements make it completely autonomous during the measurement process.

It is therefore possible to calculate:

• Charge carrier mobility
• Majority carrier density (dopants)
• Doping type (P/N ratio)
• Hall voltage / Hall coefficient
• Surface resistance, resistivity, conductivity

Features:

• Sample size: 5x5mm - 20x20mm
• Motorized dual magnets: 0.5T
• Measurement under temperature: 77K to 350K
• Current range: 1nA - 20mA

Compatibles temperature modules:

- AMP55T-RTSK: Ambient or 77K
- AMP55T-SH80350K: From 77K to 350K
- AHT55T3: From 300K to 570K
- AHT55T5: From 300K to 770K

Applications:

- Si, Ge, SiGe, SiC, GaAs, InGaAs, InP, GaN, ZnO, TCOs
- Optoelectronic component - Nanomaterials
- Sensors, MEMS - Conductive polymer
- Oxide deposit
- Ceramic & Glass
- Batteries
- Electrodes
- Photovoltaic

HMS7000Photonic Hall Effect measurement system

The HMS7000 Photonics will this time use the Van Der Pauw method under illumination to measure the response of several internal parameters of the material under different photonic stresses. This equipment is perfectly suited to the world of photovoltaics and the study of photoelectric semiconductors.

As for the other HMS series, it will characterize:

• Mobility of charge carriers
• Density of majority carriers
• The type of doping (P/N)
• Hall Voltage / Hall Coefficient
• Surface resistances, resistivity

Specifications:

• Fixed magnet: 0.51T
• "Visible illumination" photonic module (LED R,G,B)
• External source adapter (UV, IR)

Applications:

- Si, Ge, SiGe, SiC, GaAs, InGaAs, InP, GaN, ZnO, TCOs
- Optoelectronic component
- Nanomaterials
- Sensors, MEMS
- Conductive polymer
- Oxide deposit
- Ceramic & Glass
- Batteries
- Electrodes -
Photovoltaic

SRM232Hand-held 4 point probe system

The portable resistivity system is a device that offers the possibility of measuring resistivity, resistance, surface resistance or thickness on a wide variety of materials of varying sizes. Thanks to its battery operation, this system has versatile applications that can be used in various fields.

Applications:

- Si, Ge, SiGe, SiC, GaAs, InGaAs, InP, GaN, ZnO, TCO
- Oxide deposit
- Photovoltaic
- Ceramic & Glass
- Optoelectronic component
- Nanomaterials
-Sensors, MEMS
- Conductive polymer
- Batteries
- Electrodes

Specifications:

• 4 models/measurement ranges available with suitable calibrator
• Interchangeable 4-point head
• Applications: Conductivity/resistivity of layers on large panels, fuselages, bodywork... or in totally mobile measurement on an external site.

MPSMini Placer System

Very light Epoxy Die Bonder solution, MPS requires minimal training to operate.

The MPS fulfils accurate Picking and Placement of delicate devices.
Tool holder design, rocking Head, provides an easy solution for gluing.

PP6Universal Die Bonder system

It's the most versatile semi automatic Pick & Place platform.
It can be used in a wide field of applications such as ASIC, MMIC, MEMS or VECEL.

PP5 and PP6 are user friendly, flexible and requires minimal training to operate.

Eutectic and Epoxy available.

MPT10Pull Tester system

The MPT10 fulfils accurate Pull test to evaluate bond quality required for reliable process.

Accessories and appropriated tools are available to test thin bonded wires from 15µm up to 100µm diameter.
- Simple and robust
- Does not require any training to operate